Ship Handling – Using Tugs For Manoeuvring A Ship

Tugs are commonly used at sea for berthing and unberthing ships. A number of methods are used for manoeuvre a ship. 

Let’s examine the most common manoeuvres involving tugs and discuss their usage.

1. Swinging the ship

Swinging the ship

In the above picture, we can see that vessel is being swung bow to the port using two tugs, the starboard tug is pushing at the starboard bow and after tug is pushing on the port quarter. Both the tugs are pushing at their respective locations assisting in swinging the ship.

Swinging the ship

Here is a close-up view of same manoeuvre resulting in anti-clock or counter clock swing.

Swinging the ship

Now in the above picture, we can see three tugs being used for assistance. Forward tug is pushing on the port bow, aft tug on the port quarter is pulling and aft tug on starboard quarter is pushing. This will enable the ship to complete a swing with a bow to starboard or a clockwise swing.

Related Reading:

Infographic: 6 Golden rules of safe berthing

2. Berthing manoeuvre

Berthing manoeuvre

In the above picture, we can see the vessel is just off the berth and the tugs are pushing the ship onto the berth. Tugs are made fast so that when needed they can break the momentum to avoid making hard contact with the jetty. Once smoothly alongside tugs will keep on pushing till the vessel is made fast.

Both forward and after tugs need to be constantly controlled to keep the vessel absolutely parallel to the jetty.

Related Reading:

6 Common Mooring Methods Used For Ships

3. Unberthing the ship

Unberthing the ship

Two tugs are used to pull the ship off the berth in the above photo. For an unberthing, challenge will again be to pull the vessel nearly parallel to the berth to avoid either end from making contact with the jetty.

Unberthing the ship

Once the ship is safely clear from the berth, preparation for swinging can be made.

Related Reading:

Parallel Indexing Techniques For Ship Navigation

4. Single Tug Manoeuvres

Single Tug Manoeuvres

For ships fitted with a Becker rudder and controllable pitch propeller (CPP) it will be impractical to use two tugs. In such cases, the vessel can either manoeuvre without tugs altogether or will use one tug if needed.

In the above photo, spring line will be taken ashore on the mooring boat. Once ashore, this line will prevent the bow from swinging out and also the vessel will not creep ahead. At the same time, the engine movement combined with rudder will be used to get the stern alongside. The tug can be used to break the momentum if needed, as it is made fast. The tug can also be used to keep the vessel in position once alongside by pushing.

Single Tug Manoeuvres

Similarly with a bow thruster of sufficient power, depending on the ship size and manoeuvrability, one tug aft can be sufficient for berthing and unberthing.

Related Reading:

How Is Bow Thrusters Used For Maneuvering A Ship?

5. Other Uses

ship

In river ports, tugs are made fast at centre leads fore and aft to enable controlling of ship’s bow and stern while turning at tight bends where helm and engine alone will leave the ship vulnerable.

When coming alongside, tug may have to be cast off from centre lead and made fast on shoulder (forward) and quarter. This is done to help keep the ship parallel to berth and to avoid trouble with passing of mooring lines.

At busy anchorages, generally inside the harbour area, tugs can also be used for assisting commonly when both anchors are dropped to ensure that the ship’s heading remains unchanged.

Related Using:

How A Ship Is Berthed Using An Anchor?

6. How to decide on number of tugs

tug boats

Foremost consideration will be port regulations, In most of the ports, these are based on gross tonnage (GT) of a vessel being handled, while in other ports more weightage is given to length overall (LOA) of the ship for determining the number of tugs to be employed.

Most important factor, however, is the prevailing weather conditions. Both the wind and current factor need to be taken into account. For accurately knowing the effect of these forces, ship’s wind force area and underwater areas are calculated both forward/aft as well as laterally.

It is also necessary to know the direction and angle, from which, these forces will be acting on the ship’s hull.

It will be beyond the scope of this article to discuss the actual complex formulae applied and calculations involved which go to the extent of obtaining the density of air for accurate results of resultant acting forces.

Other important factors to take into account will include available under keel clearance and GM.

Bollard pull and type of tugs also factor during decision-making.

Related Reading:

What makes a ship unstable?

Understanding intact stability of ships

7. Other considerations and contingencies

In most container terminals, ships are berthed within one bollard length of each other and metal-to-metal clearance of 15-20 metres. In some tight cases, it may be down to even 10 meters. In these situations short engine kicks or adjustment of propeller pitch will help in maintaining required clearance.

But a lot of at times in busy ports, vessel ahead and astern may be berthing and/or unberthing at the same time and will have lines in the water close to ship’s propeller and thruster; then these cannot be used due to risk of fouling.

There have been cases where ships own lines have fouled the propeller and thruster.

To avoid such situation tugs are a must for safe operations.

If using only one tug, either forward or aft, the tug can check ship’s momentum in only one direction by pulling in opposite direction. This must be taken into account when planning manoeuvres with single-tug.

In some ports, it’s very common that the terminal will not be able to complete cargo operations of the previous vessel at the stipulated time and a ship, having reached, will have to hold position off the berth for several hours while waiting for the berth to be available.

At times, the ship will reach the berth and tugs will not reach on time, as they would not be free from their previous manoeuvre!

Related Reading:

Mediterranean mooring of ships

8. Final word

The most important requirement for safe mooring operations is a good Master Pilot exchange (MPX).

Tug’s bollard pull and strength of ship’s mooring bitts must be discussed to decide how much tug power can be safely used without endangering ship/tug and crew.

For berthing and unberthing, docking pilot will have the best knowledge of local conditions. She will know the limitations of tugs being used, the competence of tug crew, swinging room available, required angle and distance of towing line to best complete the manoeuvre.

Similarly, the master knows the ship and her handling characteristics and must share these details including any limitations or strange handling characteristics.

One thing to watch out for is that in almost every country pilot and tug will be communicating in the local language. Though a master should be aware of planned manoeuvres and anticipate tug actions.

But if needed, clarification must be requested and pilots world over are happy to oblige by repeating instructions if they speak English. If encountering language difficulties manoeuvre can be drawn and discussed during MPX.

Disclaimer: The authors’ views expressed in this article do not necessarily reflect the views of Marine Insight. Data and charts, if used, in the article have been sourced from available information and have not been authenticated by any statutory authority. The author and Marine Insight do not claim it to be accurate nor accept any responsibility for the same. The views constitute only the opinions and do not constitute any guidelines or recommendation on any course of action to be followed by the reader.

The article or images cannot be reproduced, copied, shared or used in any form without the permission of the author and Marine Insight. 

Do you have info to share with us ? Suggest a correction

Article Footer Banner
Article Footer Banner

Subscribe To Our Newsletters

By subscribing, you agree to our Privacy Policy and may receive occasional deal communications; you can unsubscribe anytime.

Web Stories

About Author

Capt. Ashish Joshi is presently a sailing master on container ships with a passion for teaching. At one time in his career, he used to hold classes in his ship cabin for ratings who wanted to work towards the certificate of competency! During leave, he spends time with family and on the golf course.

Leave a Reply

Your email address will not be published. Required fields are marked *